Silicon Graphics InfiniteStorage C1104-GP6 Скачать руководство пользователя страница 59

Страница: 59 / 76

Drive Bay Installation/Removal

007-6465-001

Hard Drive Carrier Assembly Usage

1. Remove the screws securing the dummy/bad drive to the hard drive carrier.

2. Insert a new/replacement hard drive into the carrier with the PCB side facing down and the

connector end toward the rear of the carrier.

3. Align the hard drive in the disk drive carrier so that the mounting holes of the carrier are

aligned with the mounting holes of the drive. Note that there may be holes in the carrier
which are marked “SATA” to aid in correct installation.

4. Secure the drive to the carrier with the screws provided. Use the M3 flat-head screws

included in the HDD bag of your accessory box.

Note:

the screws used to secure a dummy

drive to the carrier should not be used to secure the hard drive.

5. Insert the hard drive carrier assembly into its bay, keeping the carrier oriented so that the

release button is on the bottom-right. When the carrier reaches the rear of the drive bay, the
handle will retract.

6. Using your thumb, push against the upper part of the hard drive handle until the assembly

clicks into the locked (fully seated) position, see

Figure 6-4 on page 49

for an example.

Note:

Your operating system must have RAID support to enable the hot-plug capability of the

drives.

Caution:

Regardless of how many hard drives are installed, all drive carriers must remain in the

drive bays to maintain proper airflow and system cooling.

Содержание InfiniteStorage C1104-GP6













































































Результаты поиска

Содержание InfiniteStorage C1104-GP6

Отзывы:

Похожие инструкции для InfiniteStorage C1104-GP6

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage C1104-GP6, Руководство пользователя системы

Результаты поиска

Содержание InfiniteStorage C1104-GP6

Отзывы:

Похожие инструкции для InfiniteStorage C1104-GP6

Бренды по названию

Популярные бренды