Silicon Graphics InfiniteStorage C1104-GP6 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 76

background image

40

007-6465-001

5: System and Serverboard Information

drive. The operating system will be installed on the drives located in Drive positions 0 and 1.
BIOS RAID 1 and hardware RAID 1 are optionally supported for the system disk “boot”
drive.

Note that both drives 0 and 1 must be of the same type, speed and capacity.

PCIe Expansion Cards

There are two full-height PCIe 3.0 x16 expansion slots and one PCIe 3.0 x8 low-profile slot
available with the ISS C1104-GP6 servers. These external option slots function as listed:

•

External/internal PCI-Express 3.0 x8 low-profile card

•

Two external/internal PCI-Express 3.0 x16 full-height cards

Note:

Only specific cards will fit and function in the internal PCIe slots, contact your SGI sales

or service representative for information on approved cards.

Power Supply Functional Rating

The ISS C1104-GP6 server default configuration is two rear-installed 500-Watt power supplies.
The second power supply acts as a redundant power unit for the server. The supplies are
“auto-ranging” and can operate from either 100-140V or 180-240V levels at 50 or 60Hz. If either
of the two power supply modules fail, the other module will take the full load and allow the system
to continue operation without interruption. The Information (

i

)

LED on the front control panel

will blink slowly until the failed module has been replaced.

Each power supply module has its own cooling fan.

«
...
50
51
52
53
54
...
»

Содержание InfiniteStorage C1104-GP6













































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage C1104-GP6

8BIG RACK THUNDERBOLT 2

Бренд: LaCie Страницы: 28

Бренд: HPE Страницы: 174

Бренд: Xerox Страницы: 2

Бренд: Fujitsu Страницы: 280

Edgeline EL4000

Бренд: HPE Страницы: 57

ProLiant ML110 Gen10

Бренд: HPE Страницы: 101

ProLiant ML110 Gen10

Бренд: HPE Страницы: 159

@Server pSeries 630 6E4

Бренд: IBM Страницы: 651

Бренд: Gigabyte Страницы: 143

Com Port Redirector

Бренд: Lantronix Страницы: 31

Бренд: 3onedata Страницы: 3

TimeProvider 5000

Бренд: Symmetricom Страницы: 534

Бренд: Vlinx Страницы: 47

UniServer B5800 G3

Бренд: H3C Страницы: 78

Netra SPARC S7-2

Бренд: Oracle Страницы: 258

Бренд: Oracle Страницы: 148

Бренд: Technics Страницы: 32

Бренд: Gateway Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды