Silicon Graphics InfiniteStorage C1104-GP6 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 76

background image

44

007-6465-001

6: Basic Troubleshooting and Chassis Service

•

When handling chips or modules, avoid touching their pins.

•

Put the serverboard, add-on cards and peripherals back into their anti-static bags when not in
use.

•

For grounding purposes, make sure your computer chassis provides excellent conductivity
between the power supply, the case, the mounting fasteners and the serverboard.

Unpacking

Replacement components are usually shipped in anti-static packaging to avoid static damage.
When unpacking an upgrade or replacement component, make sure the person handling it is static
protected.

Control Panel

The control panel (located on the front of the chassis) must be connected to the JF1 connector on
the serverboard to provide you with system status indications. A ribbon cable has bundled these
wires together to simplify the connection. Connect the cable from JF1 on the serverboard to the
Control Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1 on both
connectors. Pull all excess cabling out of the airflow path. The LEDs inform you of system status.
See Chapter 3 for details on the LEDs and the control panel buttons.

Drive Bay Installation/Removal

This section describes hard drive installation and removal.

Accessing the Drive Bays

Drives: You do not need to access the inside of the chassis or remove power to replace or swap a
RAIDed hard disk drive. Data may be lost or corrupted if you “hot swap” a JBOD disk drive. Shut
down system power before removing or replacing a JBOD disk. Removing either a RAID or
JBOD drive without replacing it may cause system errors. Proceed to the next section for further
hard drive instructions.

«
...
54
55
56
57
58
...
»

Содержание InfiniteStorage C1104-GP6













































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage C1104-GP6

Express 5800 Series

Бренд: NEC Страницы: 90

PDS-220F Series

Бренд: ICP DAS USA Страницы: 94

Power 720 Express 8202-E4B

Бренд: IBM Страницы: 64

Бренд: IBM Страницы: 148

Бренд: IBM Страницы: 36

Бренд: IBM Страницы: 834

Бренд: IBM Страницы: 92

AMX Vision2 V2-MASTER-1210

Бренд: Harman Страницы: 2

SUPERSERVER 2048U-RTR4

Бренд: Supermicro Страницы: 152

FlexWATCH 1110L

Бренд: Seyeon Technology Страницы: 96

FusionServer G5500 V6

Бренд: xFusion Digital Technologies Страницы: 100

Бренд: MSI Страницы: 106

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

TVS-72XU Series

Бренд: QNAP Страницы: 53

QuantaGrid D51PH-1ULH

Бренд: QCT Страницы: 167

8668 - Eserver xSeries 232

Бренд: IBM Страницы: 182

BullSequana Edge nano

Бренд: Atos Страницы: 29

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды