background image

Operating manual

Twister II NA

Copyright Silca S.p.A. 2015

11

5  

MACHINE INSTALLATION AND PREPARATION 

The key-cutting machine can be installed by the purchaser and does not require any special skills.
The machine is supplied ready for use and does not need to be set up, except when changing to different tools. 
However, some checks and preparation for use need to be carried out by the operator.

5.1  

CHECKING FOR DAMAGE 

The TWISTER II NA key-cutting machine is solid and compact and will not normally damage if transport, 
unpacking and installation have all been carried out according to the instructions in this manual. However, it is 
always advisable to check that the machine has not suffered any damage.

5.2  

ENVIRONMENTAL CONDITIONS 

 To ensure that the best use is made of the TWISTER II NA key-cutting machine, certain parameters must be 
borne in mind:

 damp, badly ventilated sites should be avoided.

the ideal conditions for the machine are:
between 50 and 104 °F (10 and 40°C);   relative humidity: approximately 60 %. 

5.3  

POSITIONING  

 Place the key-cutting machine on a horizontal surface, solid 
enough to take the weight.
For comfort when using the working parts of the machine, 
the workbench should be at the same height as the 
operator’s hips.
It is important to leave clearance of at least 12” (30 cm) 
behind the machine and on each side to ensure proper 
ventilation. 

ATTENTION:  ensure that the machine voltage 

is the same as that of the power supply, which 
must be properly grounded and provided with 
a differential switch.

Fig. 8

5.4  

DESCRIPTION OF WORK STATION 

The key-cutting machine needs only one operator, who has the following controls at his/her disposal:

•  master switch (P).
•  motor start switch (Q).
• levers:

lever (C) to move the clamp carriage 

lever (I) to move the vertical carriage

Note: the letters in brackets refer to Fig. 6 on page 7.

12”

12”

12”

Содержание Twister II NA

























Отзывы: