Siko MSK210 Скачать руководство пользователя страница 27

MSK210

Transport, Storage, Maintenance and Disposal English

MSK210 · Date 

08.02.2018 · Art. 

No. 

81417 · Mod. 

status 

41/18

27

• 

The masking tape provided was not used for protecting the magnetic 

tape. The masking tape must not be magnetizable.

• 

Magnetic sensor not or incorrectly connected (pin assignment see 

chapter 

4.5

).

• 

The distance tolerances were not observed over the whole measuring 

length (see 

Fig. 6

Fig. 8

).

• 

Cable squeezed / interrupted / cut by sharp edges.

• 

The magnetic sensor has been mounted with the active side turned 

away from the band (see 

Fig. 6

Fig. 8

).

• 

Magnetic sensor has not been aligned according to 

Fig. 6

Fig. 8

.

7  Transport, Storage, Maintenance and Disposal

Transport and storage

Handle, transport and store the magnetic sensor with care. Pay attention 

to the following points:

• 

Transport and / or store the magnetic sensor in the unopened origi-

nal packaging.

• 

Protect the magnetic sensor from harmful physical influences includ-

ing dust, heat and humidity.

• 

Do not damage connections through mechanical or thermal impact.

• 

Prior to installation inspect the magnetic sensor for transport dam-

ages. Do not install damaged magnetic sensors.

Maintenance

With correct installation according to chapter 

4

 the magnetic sensor 

requires no maintenance. Clean the surface of the magnetic tape with soft 

cloth from time to time if it is very dirty.

Disposal

The magnetic sensor's electronic components contain materials that are 

harmful for the environment and are carriers of recyclable materials at the 

same time. Therefore, the magnetic sensor must be recycled after it has 

been taken out of operation ultimately. Observe the environment protec-

tion guidelines of your country.

Содержание MSK210

































Отзывы: