Siklu EtherHaul Скачать руководство пользователя страница 34

Страница: 34 / 156

EtherHaul Operation, Administration and Maintenance Manual

Page 34

Ethernet Ports Configuration and Monitoring

The Ethernet ports parameters and monitoring are managed in the

Eth Ports

page.

The EtherHaul system has the following Ethernet interfaces:



Host – Management interface



Eth0 – Radio interface (RF)



Eth1 – Line interface, port 1



Eth2 – Line interface, port 2



Eth3 – Line interface, port 3



Eth4 – Line interface, port 4

The number of line interfaces and their type (RJ45 or SFP) depend on the product used.

This chapter includes the following topics:



Settings



Advanced Settings



Maintenance



Statistics



CLI commands

5.1

Settings

Figure 5-1 Eth Ports Page: Settings

This section allows configuring the following parameters:



Port Type – RJ45 or SFP based on the physical port.

For EH-1200/TL systems with configurable port type, a radio-button allows
selecting RJ45 or SFP.



Port Enable – checkbox to enable the port.

Disable ports that are not in use so alarm will not be active (link down alarm).

Содержание EtherHaul




























































































































































Результаты поиска

Содержание EtherHaul

Отзывы:

Похожие инструкции для EtherHaul

Бренды по названию

Популярные бренды

Siklu EtherHaul, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EtherHaul

Отзывы:

Похожие инструкции для EtherHaul

Бренды по названию

Популярные бренды