Siklu EtherHaul Скачать руководство пользователя страница 130

Страница: 130 / 156

EtherHaul Operation, Administration and Maintenance Manual

Page 130

14.1.4

Radius Authentication Mode

Figure 14-2 Network Page: Users Administration

– Radius

Users are defined in the system, including name and type. The passwords are defined in
the server.

This section allows configuring the following parameters:



Authentication Mode – Radius.



Shared Secret – In Radius or Tacacs mode, Shared Secret should be entered
(identical to the one in the server). Note that is using more than one AAA server,
the servers should have the same Shared Secret.



# - Server index. Up to 5 servers can be configured. The Authentication starts
from the 1st server and goes down to the 5th.



IP Address – of the AAA server.



Protocol Port – the default port for Radius is 1812.



Accounting Port – none, SSH, HTTP, all.

Dummy Authentication is not supported for Radius (Tacacs only).

Содержание EtherHaul




























































































































































Результаты поиска

Содержание EtherHaul

Отзывы:

Похожие инструкции для EtherHaul

Бренды по названию

Популярные бренды

Siklu EtherHaul, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EtherHaul

Отзывы:

Похожие инструкции для EtherHaul

Бренды по названию

Популярные бренды