Signode AK200HDX-19 Скачать руководство пользователя страница 23

Страница: 23 / 82

After the cool off time has expired, strap release will be initiated. The camshaft rotates from

position 7 into point 8. Gripper, loop grip and vibrator move backwards to its home point 8.

The camshaft rotates from point 8 without stopping into position 9. The shutter starts opening

(sensor "Shutter close" will be de-activated) and is in fully open position at position 9 (sensor

"Shutter open" is occupied and sensor “Pre-tension reached” will be de-activated again). The

"Camshaft brake" Y38 will be activated and holds the camshaft in position until next step

"Shutter close" will be activated. At the same time the large clutch Y22 ("slow speed") de-

energises and the motor M24 rotates in idle position.

At this point, the head is moved away from the package, releasing the strap from the sealing

mechanism until limit switch "Head back to home position" (machine installation) is activated.

Next step; "Shutter close" is activated. The camshaft rotates now from position 9 into position 0.

Hereby the "strap drive brake" Y36 is activated and the camshaft brake Y38 de-activated. At the

same time the large clutch Y22 is activated.

Before reaching position 0, the sensor "Strap tension reached" will be de-activated again and

that time the large clutch Y22, motor M24 and the strap drive brake Y36 have to be deactivated.

The camshaft brake Y38 has to be activated and stops the camshaft in position 0. The camshaft

rests in position 0 and the shutter is closed. Is the sensor “shutter close” activated also, the

head is in home position and ready for further application.

This procedure is for

AK200-HDX

AK200 standard head is different.

Note:

See sequence of operation for exact time schedules. Any manual adjustment in the operational

sequence shall be done by skilled personnel only.

Содержание AK200HDX-19



















































































Результаты поиска

Содержание AK200HDX-19

Отзывы:

Похожие инструкции для AK200HDX-19

Бренды по названию

Популярные бренды

Signode AK200HDX-19, Руководство по эксплуатации, частям и безопасности

Результаты поиска

Содержание AK200HDX-19

Отзывы:

Похожие инструкции для AK200HDX-19

Бренды по названию

Популярные бренды