Signode AK200HDX-19 Скачать руководство пользователя страница 35

Страница: 35 / 82

8.10 OPERATIONAL DIFFICULTIES DURING STRAP TAKE-UP

S Y M P T O M

C A U S E

R E M E D Y

8.11

Strap is fed backwards out of the strap drive,

while the camshaft stops between points 1 and 2.

Tip of strap did not enter its end position.

Timing must be changed by reprogramming
the CPU. (Please inform service department)

Gripper support is set too tight.

Reset, see section 7.0/7.2 of the manual.

Strap in feed disturbance at strap guide
wedge.
Strap hits shutter.

Straighten chute gates or increase the bell
mouth.

Gripper support is jammed.

Remove and clean: see section 6.4 of the
manual.

8.12

Strap drive at take-up shifts too soon into low

gearing.

Gripper support is set too tight.

Reset, see section 7.0/7.2 of the manual.

Pre-tension spring for strap tension set too
soft.

Readjust pre-tension spring.

8.13

The head pulls the strap too hard down onto

the package and the camshaft does not stop shortly
before point 4.

Pre-tension spring for strap tension set too
high.

Readjust pre-tension spring.

Large clutch Y22 in transmission is defect.

Exchange transmission, see section 6.6 of the
manual, and replace exchange-transmission.

Fast switching device for clutchs is defect.

Replace fast switching devices.

8.14

Strap drive and the camshaft do not move

while the motor runs.

One or both clutches are not activated Y22,
Y37.

Inspect fuse, fast switching device and cable
terminals of transmission.

Содержание AK200HDX-19



















































































Результаты поиска

Содержание AK200HDX-19

Отзывы:

Похожие инструкции для AK200HDX-19

Бренды по названию

Популярные бренды

Signode AK200HDX-19, Руководство по эксплуатации, частям и безопасности

Результаты поиска

Содержание AK200HDX-19

Отзывы:

Похожие инструкции для AK200HDX-19

Бренды по названию

Популярные бренды