Signode AK200HDX-19 Скачать руководство пользователя страница 37

Страница: 37 / 82

8.30 OPERATIONAL DIFFICULTIES DURING "SEALING AND CUT-OFF"

S Y M P T O M

C A U S E

R E M E D Y

8.31

The strap is taken up slowly while the

camshaft stops between points 5 and 6.

Brake Y38 is not activated.

Check the switch B106 "max. strap tension".
Check connection of brake plug.

8.32

Camshaft does not reach holding point 7.

Proximity switch B105 “Pre-tension reached”
defect

Check proximity switch.

8.33

The camshaft does not stop at holding point

Proximity switch B103 "Shutter open" defect or
switch position not reached.
Proximity switch B105 “Pre-tension reached”
defect

Check proximity switch. Align sensor actuator.

8.34

The strap drive and the camshaft do not

move while the motor runs.

One or both clutches are not activated, Y22
,Y37.

Inspect fuse, fast switching device and cable
terminals of transmission.

8.35

At the backside of the joint the strap is

damaged or deformed.

Shutter does not fully open.

The proximity switch B103 "Shutter open" will
be actuated too early.

Gates on strap guide wedge get stuck.

Straighten gates.

Содержание AK200HDX-19



















































































Результаты поиска

Содержание AK200HDX-19

Отзывы:

Похожие инструкции для AK200HDX-19

Бренды по названию

Популярные бренды

Signode AK200HDX-19, Руководство по эксплуатации, частям и безопасности

Результаты поиска

Содержание AK200HDX-19

Отзывы:

Похожие инструкции для AK200HDX-19

Бренды по названию

Популярные бренды