manualshive.com logo in svg

SIG SIGRC69 HOG BIPE, Инструкция по эксплуатации, Страница: 2 / 27

Поделиться
Скачать
SIG SIGRC69 HOG BIPE Скачать руководство пользователя страница 2

.

 

Introduction

 
In order for your HOG-BIPE to fly as well as it was designed to, it must be carefully assembled. A model airplane that is not built 
properly will not fly properly! Remember to work slowly and follow the instructions exactly. SIG, as the kit manufacturer, can 
provide you with a proven aerodynamic design, quality materials, and detailed instructions, but ultimately the flyability of your 
finished model depends on how well YOU put it all together.

 

Customer Service

 
Sig Mfg. Co. is totally committed to your success in building and flying the HOG-BIPE. Should you encounter any problem 
building this kit, or find any missing or damaged parts, feel free to contact us by mail or telephone.

 

SIG MFG. CO., INC.

P.O. Box 520 
401 South Front Street 
Montezuma, IA 50171-0520 USA

PHONE: (641) 623-5154 FAX: (641) 623-3922 
SIG WEB SITE: www.sigmfg.com  
SIG E-MAIL: [email protected]

 

WARNING! THIS IS NOT A TOY!

Flying machines of any form, either model-size or full-size, are not toys! Because of the speeds that airplanes must 
achieve in order to fly, they are capable of causing serious bodily harm and property damage if they crash. IT IS YOUR 
RESPONSIBILITY AND YOURS ALONE to assemble this model airplane correctly according to the plans and 
instructions, to ground test the finished model before each flight to make sure it is completely airworthy, and to always 
fly your model in a safe location and in a safe manner. 
 
The governing body for radio-control model airplanes in the United States is the ACADEMY OF MODEL 
AERONAUTICS, sometimes referred to as the AMA. The AMA SAFETY CODE provides guidelines for the safe 
operation of R/C model airplanes. While AMA membership is not mandatory, it is a good idea and we encourage all 
new R/C fliers to join the AMA. Membership in the AMA provides you with important liability insurance protection in 
case your R/C model should ever cause serious property damage or personal injury to someone else.

For more information, contact: ACADEMY OF MODEL AERONAUTICS 

5161 East Memorial Drive Muncie, IN 47302 

Phone: (765) 287-1256

 

COMPLETE KIT PARTS LIST

Die-Cut Balsa

1 3/32"x3"x18" Die-Cut Sht.1;W-1T 

Balsa Wing Ribs

1 3/32"x3"x18" Die-Cut 

Sht.2;W-1B, W-2 Balsa Wing 
Ribs

8 3/32"x3"x18" Die-Cut Sht.3;W-

2 Balsa Wing Ribs

1 3/32"x4"x15" Die-Cut Sht.4; F-

1A,F-2,F-4,F-5A,SBR-1,SBR-
2,WTR

Balsa Sheet

1 1/16"x3"x48" Leading Edge Sheeting 

(Top Wing)

6 1/16"x3"x24" Leading Edge 

Sheeting (Top & Bottom Wing)

4 1/16"x1-1/4"x24" Trailing Edge 

Sheeting (Bottom Wing)

2 1/16"x1-1/4"x48" Trailing Edge 

Sheeting (Top Wing)

4 1/16"x3"x30" Stabilizer Sheeting

4 1/16"x3"x30" Fuselage Top 

Deck Sheeting

1 1/16"x4"x36" Wingtip Sheeting 3 1/16"x2"x36" Wing Center 

Sheeting

Balsa Sticks

2 1/4"x1/4"x36" Stabilizer Frame

1 1/4"x1/2"x48" Main Spar (Top 

Wing)

8 1/4"x1/2"x24" Main Spars 

(Bottom Wing), Stabilizer 
Leading Edge

1 1/4"x1/2"x36" Stabilizer Trailing 

Edge, Fin Post

2 1/4"x3/4"x48" Wing Trailing Edge

5 3/16"x3/16"x36" Top Deck 

Stringers

6 1/16"x1/4"x36" Cap Strips

1 1/16"x1/2"x36" Cap Strips

1 1/2" Trianglex24" Braces for Firewall, 

Bottom Wing Mount Blocks, Landing 
Gear Plate

1 1/4" Trianglex12" Brace for 

Top Wing Mount Plate

1 1/4"x1"x15" Cowl Fairing Blocks

Balsa Blocks

2 5/8"x5/8"x6" Tail Fairing Blocks

Special-Cut Balsa

2 1"x1"x3" B-5 Bottom Wing L.E. 

Blocks

1 1"x1"x1-1/2" B-4 Top Wing 

L.E. Block

1 1/2"x1-1/2"x8" Top Wing 

Center Section T.E.

2 1/2"x1-1/2"x2-1/2" Bottom 

Wing Center Section T.E. 

2 5/16x48" Leading Edge

4 1/2"x1-1/2"x24" Ailerons

2 3/8"x3"x12" Elevators

1 1/4"x3"x12" Rudder

18 1/16"x2-13/16"x1-1/8" Spar 

Webbing

Содержание SIGRC69 HOG BIPE




























Отзывы:

Нет отзывов