SIG Rascal 80 eg Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 23

SIG Rascal 80 eg Скачать руководство пользователя страница 7

7

FUSELAGE ASSEMBLY

INSTALL THE MAIN LANDING GEAR

  Locate the following parts from the kit contents:
  (1) Fuselage
  (1) Aluminum Main Landing Gear
  (3) M4 x 20 mm Socket-Head Bolts
  (3) M4 Split-Ring Lock Washers
  (2) 3" dia. Main Wheels
  (2) 4 mm dia. Axles with threaded bolt Head
  (2) 8 mm Hex Nuts; for axles
  (4) 4 mm ID Wheels Collars; for axles
  (1) Right Fiberglass Wheel Pant
  (1) Left Fiberglass Wheel Pant

(4) M3 x 12 mm Socket-Head Bolts

NOTE: We suggest you use a thread locking liquid (like Locktite

®

)

on all bolts and nuts used in the assembly of the landing gear.

❑

5) Install a Threaded Axle into the large hole of the landing gear leg,

   With  the  plain  end  of  the  axle  shaft  pointing  to  the  outside.
   Secure the axle with the 8mm Hex Nut.  When tightening the nut,
   keep the flats of the hex nut  on  the  axle  side  of  the  gear  leg
   parallel to the front edge of the leg - see photo.  This  allows  the
   hex nut to fit inside the narrow notch in the  wheel  pants  when
   they are added later.

❑

6) Slide a 4mm Wheel Collar onto the axle shaft against the head of

the Axle. Tighten the wheel collar set screw securely.

❑

7) Slide the wheel on the axle and test to make sure it spins freely

on the axle.  If it does not turn freely, drill out  the  plastic  hub  of
   the wheel with an 11/64" or #17 drill bit.

❑

8) Slide a second wheel collar onto the axle and up to the wheel.

Leave a small gap between it and the wheel, so the wheel will turn
freely, and then tighten the wheel collar set screw.

❑

9) Check the orientation of the landing gear to make sure you know

  which way is forward.  The two outer holes for mounting the gear
  to the fuselage go to the front.  Then test fit the wheel pants over
  the wheels and line up the predrilled mounting holes.  Secure the
  wheel pants in place with two M3 x 12mm socket head  bolts  for
  each pant. (You may need to  clean a little  paint out of the blind
      nuts inside the wheel pants in  order to start  the mounting bolts.
  A #11 hobby knife works well for this.)

❑

10) Attach the landing gear to the bottom of the fuselage using three

M4 x 20mm Socket-Head Bolts and three M4 Split-Ring Lock
Washers.

TAIL SURFACE AND TAILWHEEL INSTALLATION

For the following steps you will need:
(1)    Fuselage
(1)    Wing
(1)    Horizontal Stabilizer & Elevator set

(1) Vertical Fin & Rudder Set M6.5 Nylon Wing Bolts

«
...
5
6
7
8
9
...
»

Содержание Rascal 80 eg
























Отзывы:

Нет отзывов