Siemens SMIINV215R60XX Скачать руководство пользователя страница 9

Страница: 9 / 34

Page 9

Copyri

Installation Procedure

Installing the Siemens Microinverter System involves several key steps. Each step listed below is
detailed in the following pages.

Step 1

– Measure V

Step 2

– Install the AC

Step 3

– Position the

Step 4

– Attach the Microinverters to the Racking

Step 5

– Dress the

Step 6

– Connect the Microinverters

Step 7

– Terminate the unused end of the

Step 8

– Connect the Cable to

Step 9

– Ground the System

Step 10

– Complete the

Step 11

– Connect the PV Modules

Step 12

– Build the Virtual Array

DANGER

Hazardous voltage. Will cause death or serious injury.

working on this equipment.
until you have completed all of the installation procedures as described in the following
sections.

Step 1 – Measure AC at Service Entrance
Conductors

Measure AC line voltage at the service entrance conductors
to confirm AC service at the site. Acceptable ranges are
shown in the following table.

120/240 VAC or 208Y/120 V

L1 to L2

L1, L2 to neutral

2011 Siemens Industry, Inc.

Installation Procedure

Microinverter System involves several key steps. Each step listed below is

detailed in the following pages.

VAC at Service Entrance Conductors

Install the AC Junction Box

Position the Trunk and Drop Cabling

Attach the Microinverters to the Racking

Dress the Trunk and Drop Cable

Connect the Microinverters

Terminate the unused end of the Trunk and Drop Cable

Connect the Cable to AC Junction Box(es)

Ground the System

Complete the Paper Map

Connect the PV Modules

Build the Virtual Array

Hazardous voltage. Will cause death or serious injury.

Turn off Power be

working on this equipment.

DO NOT connect Siemens Microinverters to the utility grid

until you have completed all of the installation procedures as described in the following

Measure AC at Service Entrance

line voltage at the service entrance conductors

to confirm AC service at the site. Acceptable ranges are
shown in the following table.

AC or 208Y/120 VAC Single Phase

208Y/120 VAC Three

211 to 264 Vac

L1 to L2 to L3

106 to 132 Vac

L1, L2, L3 to neutral

141-00015, Rev 01

Microinverter System involves several key steps. Each step listed below is

Turn off Power before

Microinverters to the utility grid

until you have completed all of the installation procedures as described in the following

Three Phase

183 to 229 Vac

106 to 132 Vac

Содержание SMIINV215R60XX
































Результаты поиска

Содержание SMIINV215R60XX

Отзывы:

Похожие инструкции для SMIINV215R60XX

Бренды по названию

Популярные бренды

Siemens SMIINV215R60XX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SMIINV215R60XX

Отзывы:

Похожие инструкции для SMIINV215R60XX

Бренды по названию

Популярные бренды