Siemens SMIINV215R60XX Скачать руководство пользователя страница 3

Страница: 3 / 34

Page 3

2011 Siemens Industry, Inc.

141-00015, Rev 01

Table of Contents

Important Safety Information

................................................................................ 4

Read this First

.................................................................................................... 4

Symbol Legend

.................................................................................................. 4

Safety Instructions

............................................................................................... 4

The Siemens Microinver System

........................................................................... 4

How the Microinverter Works

.................................................................................. 6

System Monitoring

............................................................................................ 6

Optimal Reliability

............................................................................................ 6

Ease of Design

................................................................................................ 6

Siemens Microinverter Installation

.......................................................................... 7

Compatibility and Capacity

..................................................................................... 7

Parts and Tools Required

...................................................................................... 8

Lightning Surge Suppression

.................................................................................. 8

Installation Procedure

........................................................................................... 9

Step 1 – Measure AC at Service Entrance Conductors

................................................... 9

Step 2 – Install the AC Branch Circuit Junction Box

..................................................... 10

Step 3 – Position the Trunk and Drop Cabling

............................................................ 11

Step 4 – Attach the Microinverters to the Racking

....................................................... 12

Step 5 – Dress the Trunk and Drop Cable

................................................................ 13

Step 7 – Terminate the unused end of the Trunk and Drop Cable

.................................... 15

Step 8 – Connect the Cable to Junction Box(es)

......................................................... 16

Step 9 – Ground the System

................................................................................ 17

Step 10 – Complete the Installation Map

.................................................................. 18

Complete the Siemens Map

.............................................................................. 18

Alternative: Create Your Own Map

..................................................................... 18

Step 11 – Connect the PV Modules

........................................................................ 18

Step 12 – Build the Virtual Array

............................................................................ 19

Commissioning and Operation

............................................................................ 20

Commissioning

................................................................................................. 20

Operating Instructions

........................................................................................ 20

Troubleshooting

............................................................................................. 21

Status LED Indications and Error Reporting

.............................................................. 21

Startup LED Operation:

.................................................................................... 21

Ground Fault Detection Indicator (GFDI) Fault:

....................................................... 21

Other Faults:

................................................................................................ 21

Troubleshooting an Inoperable Microinverter

............................................................. 22

Disconnecting a Microinverter from the PV Module

...................................................... 23

Installing a Replacement Microinverter

.................................................................... 24

Technical Data

............................................................................................... 25

Technical Considerations

.................................................................................... 25

Technical Specifications

...................................................................................... 26

Siemens SMIINV215R60XX Microinverter Operating Parameters

................................. 26

Appendix

...................................................................................................... 28

Limited Warranty

............................................................................................... 28

Siemens Installation Map

.................................................................................... 30

Sample Wiring Diagram – SMIINV215R60XX, 240 Vac or 208 Vac Single Phase

................. 31

Sample Wiring Diagram – SMIINV215R60XX, 208 Vac

................................................ 32

Содержание SMIINV215R60XX
































Результаты поиска

Содержание SMIINV215R60XX

Отзывы:

Похожие инструкции для SMIINV215R60XX

Бренды по названию

Популярные бренды

Siemens SMIINV215R60XX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SMIINV215R60XX

Отзывы:

Похожие инструкции для SMIINV215R60XX

Бренды по названию

Популярные бренды