Siemens SIWAREX MS Скачать руководство пользователя страница 50

Страница: 50 / 75

Messages

and Diagnosis

7.7 Messages

via

LEDs

The LEDs on the front of the SIWAREX MS are used to signal the following status
and error messages.

Label

LED

color

LED Description

State display during

operation

SF Red

LED

System Fault

Hardware fault

OFF: No operating error
ON: Operating error

Green LED

RUN

OFF: Fatal error / defect
ON: Module flashes in
cycle: S7-CPU is stopped or
the SBR SiwaMS subroutine
is not called cyclically

NET Green

LED

Net

OFF: Scale not tared (gross
weight is output)
ON: Scaled tared (net
weight is output)

Green LED

Standstill

OFF: No standstill
ON: Standstill

Orange LED

Parameter protection

activated

OFF: Parameter protection
not activated
ON: Parameter protection
activated

→

←

Green LED

¼ d zero

OFF: Weight is outside of ¼
d zero range
ON: Weight is within ¼ d
zero range

MAX

Red LED

7 Max. exceeded

OFF: G/N weight within the
permitted weighing range
ON: Weighing range
exceeded by more than
9 numeral steps

+ 24 VDC

Green

LED 8

24 V connected

OFF: No 24 V supply
ON: 24 V supply OK

Table 7-4

List of LED messages

7-42 SIWAREX

Содержание SIWAREX MS












































































Результаты поиска

Содержание SIWAREX MS

Отзывы:

Похожие инструкции для SIWAREX MS

Бренды по названию

Популярные бренды

Siemens SIWAREX MS, Руководство по эксплуатации устройства

Результаты поиска

Содержание SIWAREX MS

Отзывы:

Похожие инструкции для SIWAREX MS

Бренды по названию

Популярные бренды