Siemens SITRANS LR 300 Скачать руководство пользователя страница 83

Страница: 83 / 140

7ML19985CL02

SITRANS LR 300 – INSTRUCTION MANUAL

Page 81

mmm

ete

P920 Reading Measurement

Displays the reading measurement that the unit is programmed for in

RUN

mode (P001,

operation).

P921 Material Measurement

Displays the reading measurement as though the unit were programmed to read Level

(P001 = 1).

P922 Space Measurement

Displays the reading measurement as though the unit were programmed to read Space

(P001 = 2).

P923 Distance Measurement

Displays the reading measurement as though the unit were programmed to read

Distance (P001 = 3).

P924 Volume Measurement

The calculated vessel capacity in Maximum Volume (P051) or % of Maximum Volume.

P927 Distance Measurement (0%)

The distance between the surface and the flange face.

Use P923 unless the distance information is required in percent.

Values (view only)

units showing Level/Space/Distance

Values

Range:

0.0000 to 99999

Related

Parameters

P051 Maximum Volume

Values

Range:

0.0000 to 99999 in units or % of Empty

Related

Parameters

P005 Units
P006 Empty

SITRANS LR 300.book Page 81 Monday, June 10, 2002 7:18 PM

Содержание SITRANS LR 300













































































































































Результаты поиска

Содержание SITRANS LR 300

Отзывы:

Siemens SITRANS LR 300, Инструкция по эксплуатации, Страница: 83 / 140

Результаты поиска

Содержание SITRANS LR 300

Отзывы: