manualshive.com logo in svg

Siemens SITRANS LR 300, Инструкция по эксплуатации, Страница: 43 / 140

Поделиться
Скачать
Siemens SITRANS LR 300 Скачать руководство пользователя страница 43

7ML19985CL02

SITRANS LR 300 – INSTRUCTION MANUAL

Page 41

m

mmmm

St

art

 Up

Accessing PROGRAM Mode

 

PROGRAM mode has two states: EDIT and DISPLAY. In DISPLAY state, the parameter 
number, parameter type, and parameter value are being displayed. In EDIT state, the EDIT 
icon 

 

indicates that the unit is accepting input into the current field. The icon remains 

visible until the ENTER key has been pressed, and the new value is accepted.

Accessing a Parameter

The parameter settings configure the units to a specific use. Press the PROGRAM key 
followed by the TOGGLE key: then choose Scroll Access or Direct Address to access a 
parameter.

Scroll Access

In PROGRAM mode, you can scroll through the parameters sequentially and in either 
direction until you reach the required parameter. [P000 to P999]

1.

The unit starts in RUN mode and 
readings correspond to existing 
settings.

2.

Press the PROGRAM key 

 to 

activate the PROGRAM mode. 
(The number fields go blank.)

3.

Press the TOGGLE key 

 

to 

display parameter fields. Initial 
program starts at P000.

1. Press ARROW 

keys to scroll 
up or down.

Note: 

Values shown are for demonstration purposes only.

Value

Parameter 
field

SITRANS LR 300.book  Page 41  Monday, June 10, 2002  7:18 PM

Содержание SITRANS LR 300













































































































































Отзывы:

Нет отзывов