Siemens SITRANS LR 300 Скачать руководство пользователя страница 29

Страница: 29 / 140

7ML19985CL02

SITRANS LR 300 – INSTRUCTION MANUAL

Page 27

mmm

Inst
allat
ion

Mounting

* Refer to the Rod Extension Requirements table on page 28.

Notes:

• The Integral process seal MUST rest on the customer flange. See detail

showing a correctly mounted unit.

• The straight/taper transition of the rod should extend past the nozzle/vessel opening.

Add extensions as required

∗

WARNING: The user is responsible for the selection of bolting and

gasket materials which will fall within the limits of the flange and

its intended use and which are suitable for the service conditions.

WARNING: Improper installation may result in loss of process

pressure.

1/2" NPT

or M 20 x 1.5

conduit entries

Straight/taper Transition

Nozzle/Vessel

Juncture

Integral Process Seal

Customer Flange

Customer-flanged
Nozzle to suit

Wiring access
cover

Minimum diameter
2" / DIN 50

Tank

Correctly Mounted Unit

Improperly Mounted Unit

Process seal should rest on flange

SITRANS LR 300.book Page 27 Monday, June 10, 2002 7:18 PM

Содержание SITRANS LR 300













































































































































Результаты поиска

Содержание SITRANS LR 300

Отзывы:

Siemens SITRANS LR 300, Инструкция по эксплуатации, Страница: 29 / 140

Результаты поиска

Содержание SITRANS LR 300

Отзывы: