Siemens SITRANS LR 300 Скачать руководство пользователя страница 35

Страница: 35 / 140

7ML19985CL02

SITRANS LR 300 – INSTRUCTION MANUAL

Page 33

mmm

Int

erc

onnect

ion

Interconnection

SITRANS LR 300 Terminal Block

Two options are available. The Intrinsically Safe mAmp Output Version has a shield
installed: the standard version does not.

Wiring requirements:

•

Increased safety, EEx e version:

solid 4

flexible stranded 2.5

•

General safety or hazardous EEx d version:

rigid 0.2 to 4

flexible stranded 0.2 to 2.5

AWG 24 to 12

Notes:

• The recommended torque on the terminal clamping screws is 0.5 – 0.6 Nm.
• Connect the shielding of instrument cables to ground at one end only.

WARNING: Avoid static discharge to terminals.

300

A special wrench is provided to
open the SITRANS LR 300
enclosure. The two lugs on the
wrench fit into the indentations
in the back cover of the
enclosure.

Lugs

Shield installed
on Intrinsically
Safe version
only

Wiring access is from the
side of the terminal block.

SITRANS LR 300.book Page 33 Monday, June 10, 2002 7:18 PM

Содержание SITRANS LR 300













































































































































Результаты поиска

Содержание SITRANS LR 300

Отзывы:

Siemens SITRANS LR 300, Инструкция по эксплуатации, Страница: 35 / 140

Результаты поиска

Содержание SITRANS LR 300

Отзывы: