Siemens SITRANS F Скачать руководство пользователя страница 311

Страница: 311 / 350

FST030
Function Manual, 04/2017, A5E35693328-AA

309

Communication

5.1

Service channel (USB)

5.1.1

USB mode (read only)

Description
The USB mode can be read in this parameter.

Options USB communication; Mass storage device (MSD)

Path

Communications → Service channel (USB) → USB mode

5.1.2

Auto mode

Description
The Auto mode can be enabled/disabled. When auto mode is enabled, a device connected

via a USB cable is always considered an MSD.

Setting Disabled; Enabled
Default

Path

Communications → Service channel (USB) → Auto mode

5.1.3

MSD connect (write only)

Description
This command is used to connect/disconnect to a mass storage device (for example: a PC).

Setting Do nothing; Connect; Disconnect
Default Do nothing

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды