Siemens SITRANS F Скачать руководство пользователя страница 180

Страница: 180 / 350

Setup

3.4 Inputs and outputs

FST030

178

Function Manual, 04/2017, A5E35693328-AA

3.4.7.8.2 Sensor alarms (1)

Description
Selection of alarm items that impact the output. Mainly sensor alarms. Applicable if Status

mode = Alarm item.

Setting 05 DSL voltages; 06 DSL Storage; 07 Flow measurement; 08 DSL internal; 09 Oil Density;

10 Oil Viscosity; 11 Oil spec. gravity; 14 Path 1: No signal; 15 Path 2: No signal; 16 Path 3:

No signal; 17 Path 4: No signal; 19 Electronics temp.; 22 Density calculation; 23 Medium

temp. calc.; 24 Pressure calculation; 25 Viscosity calculation; 26 Sensor temp. comp.; 28

Configuration 1

Default None

Path

Setup

→ Inputs and outputs → Channel 4

input/output → Status output → Sensor alarms

(1)

3.4.7.8.3 Sensor alarms (2)

Description
Selection of alarm items that impact the output. Mainly sensor alarms. Applicable if Status

mode = Alarm item.

Setting 32 Auxiliary input; 34 Invalid flow meas.; 35 Failure on CH5 or CH6; 36 Configuration 2; 37

DSL system monitor

Default None

Path

Setup → Inputs and outputs → Channel 4

input/output → Status output → Sensor alarms

(2)

3.4.7.8.4 Process alarms (1)

Description
Selection of alarm items that impact the output. Applicale if Stats mode = Alarm item.

Setting 96 Mass flow above alarm limit; 97 Mass flow above warning limit; 98 Mass flow below

warning limit; 99 Mass flow below alarm limit; 100 Volume flow above alarm limit; 101 Vol-

ume flow above warning limit; 102 Volume flow below warning limit; 103 Volume flow be-

low alarm limit; 104 Density above alarm limit; 105 Density above warning limit; 106

Density below warning limit; 107 Density below alarm limit; 108 Medium temp. above alarm

limit; 109 Medium temp. above warning limit; 110 Medium temp. below warning limit; 111

Medium temp. below alarm limit

Default None

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды