Siemens SITRANS F Скачать руководство пользователя страница 112

Страница: 112 / 350

Setup

3.4 Inputs and outputs

FST030

110

Function Manual, 04/2017, A5E35693328-AA

3.4.3.2

Active operation (read only)

Description
Shows application possibilities.

Setting Active operation not possible, use passive wiring; Active operation possible, hardware is

able to drive the current loop

Default -

Path

Setup → Inputs and outputs → Channel 1

output with HART → Active operation

3.4.3.3

PV selection

Description
Primary value - Sets a process value as primary variable. Loop current represents the

primary variable.

Setting Volume flow; Mass flow; Standard volume flow (only hydrocarbon and gas applications);

Flow velocity; Sound velocity; LiquIdent (only hydrocarbon applications); Density; Kinemat-

ic viscosity; Pressure; Medium temperature; Standard density (only hydrocarbon and gas

applications); Standard kinematic viscosity (only hydrocarbon applications); API gravity

(only hydrocarbon applications); Standard API gravity (only hydrocarbon applications);

Specific gravity (only hydrocarbon applications); Standard specific gravity (only hydrocar-

bon and gas applications); Auxiliary temperature; Sensor temperature; Standardizing factor

(only hydrocarbon and gas applications)

Default Volume flow

Path

Setup → Inputs and outputs → Channel 1

output with HART → PV se

lection

3.4.3.4

Direction

Description
Flow direction filter applicable for process values mass flow/volume flow/flow

velocity/standard volume flow rate (only hydrocarbon and gas applications).

Setting Positive; Negative; Bidirectional; Bidirectional (symmetric)
Default Positive

Path

Setup

→ Inputs and outputs → Channel 1

output with HART → Direction

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды