Siemens SITRANS F Скачать руководство пользователя страница 178

Страница: 178 / 350

Setup

3.4 Inputs and outputs

FST030

176

Function Manual, 04/2017, A5E35693328-AA

3.4.7.7.7 Pulses per amount

Description
Number of pulses which will be output when configured amount is reached.

Setting 1 to 65535
Default 1

Path

Setup → Inputs and outputs → Channel 4

input/output → Pulse output → Pulses per

amount

3.4.7.7.8 Pulse width units

Description
Units of pulse duration value used to configure Ch4 pulse width.

Setting

s (seconds); ms (milliseconds); μs (micro seconds)

Default s (seconds)

Path

Setup → Inputs & outputs → Channel 4

input/output → Pulse output → Pulse width units

3.4.7.7.9 Polarity

Description
Logical polarity of pulse output.

Setting Active high level; Active low level
Default Active high level

Path

Setup → Inputs and outputs → Channel 4

input/output → Pulse output → Polarity

3.4.7.7.10 Fail-safe behaviour

Description
Current output reaction in case of a fault.

Setting Last valid value; Hold; Current value; Fail-safe value
Default Last valid value

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды