Siemens SITRANS F Скачать руководство пользователя страница 291

Страница: 291 / 350

Maintenance and diagnostics

4.8 Simulation

FST030
Function Manual, 04/2017, A5E35693328-AA

289

Setting 0.0 Hz to 12500.0 Hz
Default 1.0 Hz
Operation mode is set to Frequency output

Setting 0.0 pulses/s - 12500.0 pulses/s
Default 0.0
Operation mode is set to Pulse output

Setting 0; 1
Default 0
Operation mode is set to Status output or Digital input

Related
Only if parameter Simulation is set to Enabled, then the setting of this parameter will be

relevant.

Path

Maintenance and diagnostics → Simulation → Simulation inputs and outputs → Channel 3

input/output → Simulation value

4.8.1.4

Relay (3)

4.8.1.4.1 Simulation

Description
Enables or disables simulation of channel 3 relay output.

Setting Disabled; Enabled
Default Disabled

Related
Only if this parameter is set to Enabled, then the setting of parameter Simulation value will

be relevant.

Path

Maintenance and diagnostics → Simulation → Simulation inputs and outputs → Channel 3

relay → Simulation

4.8.1.4.2 Simulation value

Description
Relay output value to be output when simulation is enabled.

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды