Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 64

Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 36

MAG 8000 & MAG 8000 CT

36

SFIDK.PS.026.D9.02

5. Operation

5.4.2 Battery operation

time and calculation

The battery operation time depends on the connected battery pack as well as the operation
conditions of the meter. Every 4 hours the advanced power management system calculates the
real power consumption and remaining operation capacity.

The power consumption calculation includes flow measurement, meter dialog (communication
and display) and pulse output.
The temperature is also measured to control and adjust its influence on the battery capacity.

The internal battery pack has a nominal capacity of 33 Ah giving a typical operation time of 6 years
in a revenue application. The nominal capacity of external battery packs is 66 Ah and the
operation time is limited to the lifetime of the batteries - typically 10 years. Configuration and
operation conditions

for a typical revenue application is shown in the table.

The typical operation time of 6 years is based on only 80% battery capacity and an operation time/
temperature profile of 5% @ 0 °C/32 °F, 80% @ 15 °C/59 °F and 15% @ 50 °C/122 °F.

The leakage detection, in the advance version, will affect the battery operation time if a higher
excitation frequency is selected during leakage period.

The effect from other temperatures can be seen from the figure.
A variation in temperature from 15 °C to 55 °C (59 °F to 131 °F) reduces the capacity by 17%.
(In the table from 15 Ah to 12½ Ah).

Note

Physical installation of the battery pack may
influence the battery capacity. Optimal battery
capacity is achieved with the battery pack in
an upright position.

Excitation frequency

(24 hours operation)

1/30 Hz

1/15 Hz

1/5 Hz

1.5625 Hz

3.125 Hz

6.25 Hz

Two D-Cell battery

DN 25...200

8 year

6 year

40

8 months

4 months

2 months

33 Ah Internal

(1"...8")

months

battery pack

DN 250…600

6 year

4 year

20

4 months

2 months

NA

(10"...24")

months

Four D-Cell battery DN 25...200

10 year

10 year

80

16 months

8 months

4 months

66 Ah External

(1"...8")

months

battery pack

DN 250…600

10 year 8 year

40

8 months

4 months

NA

(10"..24")

months

Scenario - Revenue application

Output A

Pulse - 10 Hz

Output B

Alarm or Call up

Meter dialog

1 hour per month

Excitation frequency

1/15 Hz

Country main frequency

50 Hz / 60 Hz

«
...
34
35
36
37
38
...
»

Содержание SITRANS F M MAG 8000

































































Отзывы:

Нет отзывов