manualshive.com logo in svg

Siemens SIPROTEC 7SD80, Руководство пользователя

Поделиться
Скачать
Siemens SIPROTEC 7SD80 Скачать руководство пользователя страница 274

Mounting and Commissioning

3.3 Commissioning

SIPROTEC, 7SD80, Manual

E50417-G1140-C474-A1, Release date 09.2011

274

Polarity Check

If the device is connected to voltage transformers, the local measured values already allow a polarity check.

A load current of at least 5% of the rated operational current is still required. Any direction is possible but must 
be known. 

  

• With closed circuit breakers, the power values are viewed as primary and secondary values on the front 

display panel or via the operator or service interface with a personal computer.

• The measured power values on the actual device or in DIGSI enable you to verify that they correspond to 

the load direction (Figure 3-30):

P

 positive, if active power flows into the protected object,

P

 negative, if active power flows towards the busbar,

Q

 positive, if (inductive) reactive power flows into the protected object,

Q

 negative, if reactive power flows toward the busbar.

Therefore, the power results and their components must have opposite signs at both ends.

It must be taken into consideration that high charging currents, which might occur with long overhead lines 
or with cables, are capacitive, i.e. correspond to a negative reactive power into the line. In spite of a resistive-
inductive load, this may lead to a slightly negative reactive power at the feeding end whereas the other end 
shows an increased negative reactive power. The lower the load current for the test, the higher the signifi-
cance of this influence. In order to get unambiguous results, you should increase the load current if neces-
sary.

Figure 3-30

Apparent load power

Содержание SIPROTEC 7SD80

































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды