Siemens SINAMICS G120P CU230P-2 Скачать руководство пользователя страница 48

Страница: 48 / 52

Commissioning

4.4 Frequently required parameters

CU230P-2 Control Units

Compact Operating Instructions, 01/2016, A5E37058917B AA

Parameter Explanation
p1900

Motor data identification and rotating measurement
0: Locked

1: Identify motor data and optimize the speed controller

2: Identify motor data (at standstill)

3: Optimize the speed controller (rotating in operation)

11: Ident. motor data and opt. speed controller, change to operation (not available with PM230 or PM250

Power Module)

12: Identify motor data (at standstill), change to operation (not available with PM230 or PM250 Power Mod-

ule)

p2030

Fieldbus interface protocol

selection

The possible settings depend on the Control Unit:
0: No protocol

1: USS

2: Modbus RTU

3: PROFIBUS

5: BacNet

7: PROFINET

8: P1

10: EtherNet/IP

r2050

Words received via fieldbus (16 bit)
r2050[0]: PZD01 … r2050[11]: PZD12

p2051

Words sent via fieldbus (16 bit)
p2051[0]: PZD01 … p2051[16]: PZD17

p2080

Binector-connector converter, status word 1
p2080[0]: Bit 0 … p2080[15]: Bit 15

r2090

PROFIdrive PZD1 receive bit-by-bit (control word 1)
r2090.00: Bit 0 … r2090.15: Bit 15

p2200

Technology controller enable 1: Technology controller is enabled

p2201 …

p2215

Technology controller fixed value 1 ... 15

p2220 …

p2223

Technology controller fixed value selection bit 0 ... 3

r2224

Technology controller fixed value active

p2253

Technology controller setpoint 1

p2254

Technology controller setpoint 2

p2257

Technology controller ramp-up time

p2258

Technology controller ramp-down time

p2264

Technology controller actual value

p2265

Technology controller actual value filter time constant

p2267

Technology controller upper limit actual value

p2268

Technology controller lower limit actual value

p2271

Technology controller actual

value inversion (sensor type)

0: No inversion

1: invert actual value signal (this should be set if the actual value decreases

with increasing motor speed)

p2274

Technology controller differentiation time constant

p2280

Technology controller proportional gain

p2285

Technology controller integral time

p2293

Technology controller ramp-up/ramp-down time

Содержание SINAMICS G120P CU230P-2





















































Результаты поиска

Содержание SINAMICS G120P CU230P-2

Отзывы:

Бренды по названию

Популярные бренды

Siemens SINAMICS G120P CU230P-2, Краткое руководство по эксплуатации

Результаты поиска

Содержание SINAMICS G120P CU230P-2

Отзывы:

Бренды по названию

Популярные бренды