Siemens SINAMICS G110 Скачать руководство пользователя страница 30

Страница: 30 / 92

Installation

04/2005

SINAMICS G110 Operating Instructions

6SL3298-0AA11-0BP0

♦

Free from dents and holes.

♦

Made of metal (steel or aluminium).

♦

Must not be painted.

♦

Must be free from rust.

5. Apply coating of heatsink/thermal contact paste to the inverter’s flat plate.

6. Ensure that the contact paste is spread evenly over the rear surface of the

Flat Plate.

7. Mount the inverter using four M4 screws.

8. Ensure that the inverter is mounted securely and the M4 screws are

tightened to the correct torque of 2.5 Nm (22.12 lbf.in).

9. If required, connect the external heatsink on the other side of the rear

plate, ensuring an evenly spread thermal contact paste is apply.

10. When the installation is completed the effectiveness of the cooling should

be verified by a load test.

11. Check that there is no trip F0004.

Table 2-3

Flat Plate Power Losses and Thermal Specifications*

120 W

250 W

370 W

550 W

750 W

Operating temperature range (ºC)

-10 to +50

-10 to +40

Total losses (W)

Lineside and control losses (W)

Recommended thermal resistance
of heatsink (K/W)

3.0 2.2 1.6 1.2 1.2

Recommended output current (A)

0.9

1.7

2.3

3.2

3.9

*The losses given in Table 2-3 are applicable for units fitted with 25 m of screened cable

Содержание SINAMICS G110





























































































Результаты поиска

Содержание SINAMICS G110

Отзывы:

Похожие инструкции для SINAMICS G110

Бренды по названию

Популярные бренды

Siemens SINAMICS G110, Руководство по эксплуатации

Результаты поиска

Содержание SINAMICS G110

Отзывы:

Похожие инструкции для SINAMICS G110

Бренды по названию

Популярные бренды