Siemens SINAMICS G110 Скачать руководство пользователя страница 52

Страница: 52 / 92

Commissioning 04/2005

SINAMICS G110 Operating Instructions

6SL3298-0AA11-0BP0

Once the cloning procedure has started, it cannot be interrupted.

It is possible to copy data from inverters of different power and voltage ratings.

During download, if the data is not compatible with the inverter, the default

values for the parameter will be written to the inverter.

During the cloning process any data already held by the BOP is overwritten.

If the download or upload of data fails, the inverter will not function correctly.

Note

1. After cloning parameters between differing variants of the SINAMICS G110

inverters (i.e. Analog to USS or USS to Analog) the following parameter must
be checked:

P0719 – Selection of command and frequency setpoint

P1000 – Selection of frequency setpoint.

2. When cloning parameter sets associated with different firmware releases using

the BOP, it should be noted that for new parameters, the default value is
entered.

Содержание SINAMICS G110





























































































Результаты поиска

Содержание SINAMICS G110

Отзывы:

Похожие инструкции для SINAMICS G110

Бренды по названию

Популярные бренды

Siemens SINAMICS G110, Руководство по эксплуатации

Результаты поиска

Содержание SINAMICS G110

Отзывы:

Похожие инструкции для SINAMICS G110

Бренды по названию

Популярные бренды