Siemens Simotion TM 121C Скачать руководство пользователя | Manualshive

Страница: 59 / 76

background image

Procedural functions of press brakes

© Siemens AG 2003 All Rights Reserved
SIMOTION Safety Unit (AP) - Edition 06.2003

7-59

7.6 Information

on

functionality

7.6.1

Conditions for fast downward movements

•

Foot control

To be able to initiate a rapid downward movement by foot control, the access
protection that is activated in the respective operating mode must supply the
enable (HIGH level). If access protection has not been parameterized in the
respective operating mode, a fast downward movement cannot be initiated by
foot control.

•

Two-hand control (two-hand/foot control)

According to the EN 12622 standard,

two-hand control is only permissible in

the Setup mode.
If the fast downward movement is to be initiated by two-hand control up to the
MUTE point during operation, access protection is not required. A MUTE point
must be parameterized for this function. Switching of the valve is initiated at the
MUTE point (slow speed). A stop can now be initiated via the "DOWN" request
signal and control can be switched to foot control (foot mode ).

7.6.2 Tilt

monitor

Figure 7-9 Tilt monitor

Two one-channel proximity switches can be connected under the "Generate
enable" menu item using the two external safety devices. This function is fail-safe
(HIGH level for enable).
The proximity switches must be installed on the machine according to the desired
maximum tilt.

«
...
57
58
59
60
61
...
»

Содержание Simotion TM 121C













































































Отзывы:

Нет отзывов

Похожие инструкции для Simotion TM 121C

Бренд: Sabre Страницы: 50

Бренд: SAFERA Страницы: 15

Бренд: Comelit Страницы: 77

Бренд: Lupus Electronics Страницы: 148

Бренд: Survitec Group Страницы: 2

ORO-SENSO-MIC-1

Бренд: LED-POL Страницы: 4

Бренд: NST Страницы: 2

Бренд: FLIR Страницы: 2

1092/601 THERA 4 MINIDOME P/T/Z

Бренд: urmet domus Страницы: 136

Бренд: Visonic Страницы: 11

SUCCESS-438.15N

Бренд: technoac Страницы: 30

Бренд: Q-See Страницы: 11

Бренд: Agatec Страницы: 33

Бренд: Zamel Страницы: 8

Бренд: Luceat Страницы: 4

Бренд: Hanwha Vision Страницы: 22

Бренд: Hanwha Vision Страницы: 25

Бренд: Hanwha Vision Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды