Siemens SIMATIC NET SCALANCE W748-1 Скачать руководство пользователя

Страница: 28 / 78

Description of the device

4.4 Accessories

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

Type

Properties

Article number

ANT795-4MD

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, 90°

connector.

6GK5795-4MD00-0AA3

ANT795-4MX

Omnidirectional antenna, 2/2.5 dBi,

2.4 GHz and 5 GHz, IP69K, N-Connector

male

6GK5795-4MX00-0AA0

ANT795-6DC

Wide angle antenna, mast/wall mounting,

9 dBi 2.4 GHz and 5 GHz, N-Connect

female

6GK5795-6DC00-0AA0

ANT795-6MN

Omnidirectional antenna, mounted on

roof/vehicle, 6/8 dBi 2.4 GHz and 5 GHz,

N-Connect female

6GK5795-6MN10-0AA6

ANT795-6MT

Omnidirectional antenna (MIMO),

mounted on roof/vehicle/ceiling, 5/7 dBi

2.4 GHz and 5 GHz, 3 x QMA connector

female

6GK5795-6MT00-0AA0

ANT795-6MP

Omnidirectional antenna, 5/7 dBi, 2.4 GHz

and 5 GHz, IP65/67, N-Connector female

6GK5795-6MP00-0AA0

IWLAN RCoax Cable

2,4 GHz PE 1/2"

Omnidirectional antenna, 0 Bi 2.400 -

2.485 GHz, N-Connect female

6XV1875-2A

IWLAN RCoax Cable

5 GHz PE 1/2"

Omnidirectional antenna, 0 Bi 5.150 -

5.875 GHz, N-Connect female

6XV1875-2D

NOTICE
ANT795-4MA

The ANT795-4MA antenna has degree of protection IP30 and is therefore only suitable

for dry environments.

Note
ANT793-8DJ

The antenna ANT793-8DJ may only be used with the flexible connecting cable 6XV1875-

5CH50 (5 m length) or 6XV1875-5CN10 (10 m length). Other flexible connecting cables

are not permitted.

Notice for USA/Canada

Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2).

Note
ANT793-8DK

The antenna ANT793-8DK may only be used with the flexible connecting cable 6XV1875-

5CN10 (10 m length). Other flexible connecting cables are not permitted.

Notice for USA/Canada

Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2).

Содержание SIMATIC NET SCALANCE W748-1















































































Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W748-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE W748-1, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W748-1

Бренды по названию

Популярные бренды