Siemens SIMATIC NET SCALANCE W748-1 Скачать руководство пользователя

Страница: 59 / 78

SCALANCE W788-x / W748-1
Operating Instructions, 03/2022, A5E03678333-17

Maintenance and cleaning

WARNING

Unauthorized repair of devices in explosion-proof design

Risk of explosion in hazardous areas
•

Repair work may only be performed by personnel authorized by Siemens.

WARNING

Impermissible accessories and spare parts

Risk of explosion in hazardous areas
•

Only use original accessories and original spare parts.

•

Observe all relevant installation and safety instructions described in the manuals for

the device or supplied with the accessories or spare parts.

CAUTION

Hot surfaces

Risk of burns during maintenance work on parts with a surface temperature above

70 °C (158 °F).
•

Take appropriate protective measures, for example, wear protective gloves.

•

Once maintenance work is complete, restore the touch protection measures.

NOTICE
Cleaning the housing

If the device is not in a hazardous area, only clean the outer parts of the housing with a

dry cloth.
If the device is in a hazardous area, use a slightly damp cloth for cleaning.
Do not use solvents.

Содержание SIMATIC NET SCALANCE W748-1















































































Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W748-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE W748-1, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W748-1

Бренды по названию

Популярные бренды