Siemens SIMATIC NET SCALANCE W748-1 Скачать руководство пользователя страница 50

Страница: 50 / 78

Connecting up

6.1 Safety when connecting up

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

WARNING

EXPLOSION HAZARD

Do not press the reset button if there is a potentially explosive atmosphere.

WARNING

Unsuitable cables or connectors

Risk of explosion in hazardous areas
•

Only use connectors that meet the requirements of the relevant type of protection.

•

If necessary, tighten the connector screw connections, device fastening screws,

grounding screws, etc. according to the specified torques.

•

Close unused cable openings for electrical connections.

•

Check the cables for a tight fit after installation.

WARNING

Lack of equipotential bonding

If there is no equipotential bonding in hazardous areas, there is a risk of explosion due

to equalizing current or ignition sparks.
•

Ensure that equipotential bonding is available for the device.

WARNING

Unprotected cable ends

There is a risk of explosion due to unprotected cable ends in hazardous areas.
•

Protect unused cable ends according to IEC/EN 60079-14.

WARNING

Improper installation of shielded cables

There is a risk of explosion due to equalizing currents between the hazardous area and

the non-hazardous area.
•

Ground shielded cables that cross hazardous areas at one end only.

•

Lay a potential equalization conductor when grounding at both ends.

Содержание SIMATIC NET SCALANCE W748-1















































































Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE W748-1, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Бренды по названию

Популярные бренды