Siemens SIMATIC NET SCALANCE W748-1 страница 39 Скачать руководство пользователя

Страница: 39 / 78

Installation and removal

5.1 Safety notices for installation

SCALANCE W788-x / W748-1
Operating Instructions, 03/2022, A5E03678333-17

Safety notices when using according to FM

If you use the device under FM conditions you must also keep to the following safety

notices in addition to the general safety notices for protection against explosion:

WARNING

EXPLOSION HAZARD

The equipment is intended to be installed within an enclosure/control cabinet. The

inner service temperature of the enclosure/control cabinet corresponds to the ambient

temperature of the module. Use cables with a maximum permitted operating

temperature of at least 20 °C higher than the maximum ambient temperature.

WARNING

Wall mounting is only permitted if the requirements for the housing, the installation

regulations, the clearance and separating regulations for the control cabinets or

housings are adhered to. The control cabinet cover or housing must be secured so that

it can only be opened with a tool. An appropriate strain-relief assembly for the cable

must be used.

WARNING

Wall mounting outside of the control cabinet or housing does not fulfill the

requirements of the FM approval.

Note

You must not install the device on a wall in hazardous areas.

Содержание SIMATIC NET SCALANCE W748-1















































































Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W748-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE W748-1, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET SCALANCE W748-1

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE W748-1

Бренды по названию

Популярные бренды