Siemens SIMATIC NET CP 343-1 Скачать руководство пользователя страница 41

Страница: 41 / 78

Installation, connecting up and commissioning

5.3 Connecting the CP to Ethernet

CP 343-1
Manual, 12/2018,

C79000−G8976−C201

-08

Note
Autocrossing mechanism - effects on the connectors
For small local area networks or for attaching several Ethernet devices, a 2port switch

has been integrated on the PROFINET interface of the CP.
With the autocrossing mechanism integrated in the switch, it is possible to use a standard

cable to connect the PG/PC. A crossover cable is not necessary.

Please note the following points:

•

Manual configuration
If a port is set to manual configuration and autonegotiation is disabled, the

autocrossing mechanism is also disabled for this port. Which cable you need to use

depends on the partner device (network component or end device).
In the factory, the ports are set for automatic configuration.
For more information, refer to section Network settings (Page 47)

•

Connecting switches
If you connect further switches, make sure that no ring is formed in the network.

Figure 5-2

Connecting switches

Note
MRP configuration
With an MRP configuration, keep to the setup guidelines for MRP.

You will find examples of network attachments in the general Part A of this manual, see

/1/ (Page 71).

Содержание SIMATIC NET CP 343-1















































































Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET CP 343-1, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды