Siemens SIMATIC NET CP 343-1 Скачать руководство пользователя страница 52

Страница: 52 / 78

Configuration and operation

6.9

Timeofday synchronization

CP 343-1

Manual, 12/2018,

C79000−G8976−C201

-08

6.9

Timeofday synchronization

General rules

The CP supports the two modes explained below for timeofday synchronization:

●

SIMATIC mode

●

NTP mode (NTP: Network Time Protocol)
No automatic changeover to daylight saving time is defined in NTP. As a result, you may

need to implement this changeover using a program application.

Project engineering

For more detailed information on configuration, refer to the online help of the "Time-of-day

synchronization" parameter group and in Part A of the manual /1/ (Page 71).

6.10

SNMP agent

SNMP (Simple Network Management Protocol)

SNMP is a protocol for managing networks. To transmit data, SNMP uses the

connectionless UDP protocol.
The information on the properties of SNMPcompliant devices is entered in MIB files (MIB =

Management Information Base).
The CP supports data queries via SNMP in Version 1. It returns the contents of certain MIB

objects according to the MIB II standard, LLDP MIB, Automation System MIB and

MRP Monitoring MIB.

MIB file and SNMP profile file

You will find the MIB file and the SNMP profile file of the module in the STEP 7 installation in

the folders "S7DATA" > "snmp" under the name of the module.

Further information

For more detailed information on working with MIB files, refer to the documentation of the

SNMP client you are using (example of an SNMP client: SNMP OPC server from

SIMATIC NET).

You will find more information on MIBs on the following SIMATIC

NET Internet page:

15177711 (

http://support.automation.siemens.com/WW/news/en/8797900

)

Содержание SIMATIC NET CP 343-1















































































Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET CP 343-1, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды