Siemens SIMATIC NET CP 343-1 Скачать руководство пользователя страница 61

Страница: 61 / 78

Service and maintenance

7.4 Replacing a module

CP 343-1
Manual, 12/2018,

C79000−G8976−C201

-08

The CP 343-1 (EX30) can be used along with a dummy module SM370

(6ES7

370-0AA01-0AA0) in any double width slot of an existing S7-300 rack. The SM370

dummy module has a switch on the rear that you need to set to the position "NA" in this

case.

Interface in the user program

Note
Remember that if you replace a module, you must only use the blocks permitted for the

configured CP type on the SEND/RECEIVE interface in the user program. It is advisable to

always use the current block versions.
If you use the module described here as replacement for the modules listed below, the

blocks listed following this list must be used:
Modules used:

•

6GK7

343-1EX10-0XE0

•

6GK7

343-1EX11-

0XE0 configured as 6GK7

343-1EX10-0XE0.

Block versions to be used:

•

AG_SEND (as of V4.2)

•

AG_RECV (as of V4.7)

•

AG_LOCK (as of V4.0)

•

AG_UNLOCK (as of V4.0)

Note
Always use

the latest block versions for new user programs. You will find information on the

current block versions and the current blocks for downloading on the Internet under:
Link: (

https://support.industry.siemens.com/cs/ww/en/ps/15342/dl

)

Module replacement

Please follow the procedure below when replacing an older module with the module

described here:

Содержание SIMATIC NET CP 343-1















































































Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET CP 343-1, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды