Siemens SIMATIC Ident CB Gate Скачать руководство пользователя страница 33

Страница: 33 / 70

Network integration

6.3 Structure of the data block

SIMATIC Ident CB Gate
Operating Instructions, 08/2022, C79000-G8976-C671-01

Table 6- 4

Structure of the "MCSInterface" data block

Variable

Data type

Offset

TCP

Comment

Interface.

FromMCS

STRUCT

0.0

Structure that is received

from the higher-level system.

EnableGate

BOOL

0.0

Enable gate.

DisableGate

BOOL

0.1

Disable gate.

ResetGate

BOOL

0.2

Reset gate.

ResetStatistic

BOOL

0.3

Reset statistics.

Reserve04

BOOL

0.4

Reserve05

BOOL

0.5

Reserve06

BOOL

0.6

Reserve07

BOOL

0.7

ConveyorSpeed

REAL

2.0

Interface.

ToMCS

STRUCT

6.0

0.0

Structure that is sent to the

higher-level system

GateEnabled

BOOL

6.0

0.0

Gate is enabled.

InWork

BOOL

6.1

0.1

Read operation active.

FinishedWith

Data

BOOL

6.2

0.2

Read operation with data

ended.

Finished

WithoutData

BOOL

6.3

0.3

Read operation without data

ended because no transponder

was clearly identified.

FinishedObject

Lost

BOOL

6.4

0.4

Read operation was aborted

because the previous object

is still being processed.

Reserve5

BOOL

6.5

0.5

Reserve6

BOOL

6.6

0.6

Reserve7

BOOL

6.7

0.7

Reserve10

BYTE

7.0

1.0

Reserve

WORD

8.0

2.0

TelegramID

UNIT

10.0

4.0

ID of sent telegram.

Is incremented when a

telegram is sent.

Range of values 1...65535.

ResultID

UNIT

12.0

6.0

ID of the result.

Is incremented on each new

result.

Range of values 1...65535.

Orientation

INT

14.0

8.0

Alignment of the object

•

0 = Unknown

•

1 = Tag top

•

2 = Tag bottom

Transponder

IID_IN_I_8

16.0

10.0

Transponder data of the

detected transponder

Reserved

BYTE

16.0

10.0

ID_Len

BYTE

17.0

11.0

Length of the EPC ID

EPC_ID

ARRAY

[1..62] of

Byte

18.0

12.0

EPC ID

tagPC

WORD

80.0

74.0

RSSI

BYTE

82.0

76.0

RSSI value

MaxRSSI

BYTE

83.0

77.0

Highest RSSI value

MinRSSI

BYTE

84.0

78.0

Lowest RSSI value

channel

BYTE

85.0

79.0

Channel

Содержание SIMATIC Ident CB Gate







































































Результаты поиска

Содержание SIMATIC Ident CB Gate

Отзывы:

Похожие инструкции для SIMATIC Ident CB Gate

Бренды по названию

Популярные бренды

Siemens SIMATIC Ident CB Gate, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC Ident CB Gate

Отзывы:

Похожие инструкции для SIMATIC Ident CB Gate

Бренды по названию

Популярные бренды