Siemens SIMATIC Ident CB Gate Скачать руководство пользователя страница 36

Страница: 36 / 70

Aligning and configuring

7.1 Aligning antennas

SIMATIC Ident CB Gate

Operating Instructions, 08/2022, C79000-G8976-C671-01

Procedure

Follow these steps to fundamentally align the antennas to the top read point (Readpoint_1):
1.

Position an object on the conveyor system in such a way that the transponder of the object

is approx. 20 cm behind the CB Gate.
Note that the exact alignment of the antennas depends on the height of the objects on

the conveyor system. When positioning, make sure that the transponder of the object is at

the top.

Align the antennas

①

and

②

to the transponder.

Figure 7-1

Aligning antennas

Open the WBM of the reader and switch to the menu "Settings > Align antenna".

In the "Basic settings", select the antenna

①

and click the button "Start alignment".

Align the antenna

①

in such a way that it detects the transponder with the highest and

most stable RSSI value possible during each read operation.

Secure the antenna

①

Click on the "Stop alignment" button.

Repeat steps 4 to 7 for the antenna

②

Содержание SIMATIC Ident CB Gate







































































Результаты поиска

Содержание SIMATIC Ident CB Gate

Отзывы:

Похожие инструкции для SIMATIC Ident CB Gate

Бренды по названию

Популярные бренды

Siemens SIMATIC Ident CB Gate, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC Ident CB Gate

Отзывы:

Похожие инструкции для SIMATIC Ident CB Gate

Бренды по названию

Популярные бренды