Siemens SIMATIC Ident CB Gate Скачать руководство пользователя страница 26

Страница: 26 / 70

Connecting

5.1 Connecting the system components

SIMATIC Ident CB Gate

Operating Instructions, 08/2022, C79000-G8976-C671-01

Procedure: Connecting antennas

Follow these steps to connect the antennas to the reader:
1.

Connect the top-left antenna (see also graphic in section "Mounting (Page 21)") to the

antenna connector "ANT1" of the reader using the antenna connection cable (3 m).

Connect the top-right antenna to the antenna connector "ANT2" of the reader using the

antenna connection cable (5 m).

If necessary, connect the bottom-left antenna to the antenna connector "ANT3" of the

reader using the antenna connection cable (3 m).

If necessary, connect the bottom-right antenna to the antenna connector "ANT4" of the

reader using the antenna connection cable (5 m).

Secure the antenna connection cable with the cable ties pre-mounted on the mounting rails.
Observe the minimum permissible bending radius of 51 mm, which must not be

undershot.
Make sure that the antenna connection cable is secured in such a way that there is still

sufficient play if the antennas are adjusted later and there is no strain on the antenna

connectors.

Power supply connection and other connections

Finally, you need to connect the power supply unit of the CB Gate to an external power

supply (safety plug ⇒ socket).

If you want to integrate the CB Gate into a higher-level system, you need to connect the

switch to a higher-level system (e.g. a controller or a PC) with an Ethernet cable or to a switch

integrated in the system. To integrate the CB Gate into your existing switch, connection via a

SCALANCE S is recommended.
You can find detailed information on creating a cell protection concept based on a SCALANCE

S at the following link:
Understanding and Using Firewall of Industrial Security Appliance SCALANCE S

(

https://support.industry.siemens.com/cs/de/en/view/22376747

)

Содержание SIMATIC Ident CB Gate







































































Результаты поиска

Содержание SIMATIC Ident CB Gate

Отзывы:

Похожие инструкции для SIMATIC Ident CB Gate

Бренды по названию

Популярные бренды

Siemens SIMATIC Ident CB Gate, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC Ident CB Gate

Отзывы:

Похожие инструкции для SIMATIC Ident CB Gate

Бренды по названию

Популярные бренды