Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 63

Страница: 63 / 126

Programming

5.6 Diagnostic function blocks

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)

Manual, 06/2019, A5E46959434-AA

Parameter

Declaration Data type Memory

area

Description

ADDR_S

TATUS

BYTE

Show the control status of the device:

•

1: Normal status

•

2: No device with the short address

•

3: The DALI device displays an error frame. This error may be

caused by the short address conflict or the problem of the DALI

device.

•

4: Type mismatch. The configured type is not the same as the

actual one.

•

5: The number of instances mismatch. The configured number

of instances is different from the physical device.

•

15: This short address of sensor device is assigned to CM

1xDALI.

DEV_ST

ATUS

BYTE

Show the status of the input devices.
For the detailed explanation for each Bit of DEV_STATUS, refer to

the following section "Parameter DEV_STATUS".

CFG_NU

M_OF_I

NST

BYTE

•

When CONFIGURED = 0, the value of CFG_NUM_OF_INST is

•

When CONFIGURED = 1, the value of CFG_NUM_OF_INST is

the configured number of instances.

NUM_OF

_INST

USInt

The actual number of sensor instances in the device.
Range: 0 to 32

INST_ER

Ar-

ray[0..31]

of BOOL

INST_ERR = 1: Error occurs in the instance.
The index of the array indicates the instance number.

INST_AC

TIVE

Ar-

ray[0..31]

of BOOL

INST_ACTIVE = 1: The instance is active.
The index of the array indicates the instance number.

CFG_IN

ST_TYP

Ar-

ray[0..31]

of USInt

Configured instance type of each sensor instance.
The index of the array indicates the instance number.

INST_TY

Ar-

ray[0..31]

of USInt

Actual instance type of each sensor instance.
The index of the array indicates the instance number.

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы:

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 63 / 126

Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы: