Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 62

Страница: 62 / 126

Programming

5.6 Diagnostic function blocks

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)
Manual, 06/2019, A5E46959434-AA

Parameter

The following table shows the parameters of the function block:

Parameter

Declaration Data type Memory

area

Description

READ

Input

BOOL

I, Q, M, D,

L or Con-

stant

Query the status of sensor upon a rising edge.

ADDRESS

USInt

I, Q, M, D,

L or Con-

stant

Specify the short address of the device.
Range: 0 to 63

CM_DALI

InOut

"DALI_CT

RL"

The data block of DALI_CTRL specifies the CM 1xDALI which

communicates with the current function block.

BUSY

Output

BOOL

I, Q, M, D,

Status parameter:

•

BUSY = 0: Processing of job is terminated.

•

BUSY = 1: Job is still being committed.

ACTIVE

BOOL

I, Q, M, D,

Status parameter:

•

ACTIVE = 0: Job is not yet started.

•

ACTIVE = 1: Job is being executed.

DONE

BOOL

I, Q, M, D,

Status parameter:

•

DONE = 0: Job is not yet started or still executing.

•

DONE = 1: Job is executed without errors.

ERROR

BOOL

I, Q, M, D,

Status parameter:

•

ERROR = 0: No error occurs.

•

ERROR = 1: Error occurs during processing.

STATUS

BYTE

I, Q, M, D,

When ERROR = 0,

STATUS has following

three values:

•

16#00: Idle

•

16#01: Executing

•

16#7F: Completed

When ERROR = 1, STATUS shows the

detailed error code. For the detailed

meaning of each error code, refer to Pa-

rameter STATUS (Page 106).

SENSOR_S

TATUS

SensorSta

Sta-

tusDetail

D, L

The status information of sensor

CONFIG

URED

BOOL

CONFIGURED = 1: The short address is configured by using

DALI_SENSOR_ADD (Page 89) or DALI_DEV_UPLOAD

(Page 100).

ADDR_C

HANGE

BOOL

•

ADDR_CHANGED = 0: The short address of sensor is not

changed.

•

ADDR_CHANGED = 1: The short address of sensor is changed

during the scan procedure.

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы:

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 62 / 126

Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы: