manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 53 / 126

Поделиться
Скачать
Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 53

Programming 

 

5.6 Diagnostic function blocks 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

52

 

Manual, 06/2019, A5E46959434-AA 

5.6

 

Diagnostic function blocks 

Diagnostic function blocks are used for querying the status information of all the DALI 

devices. 

5.6.1

 

DALI_DEV_GTIN 

Description 

DALI_DEV_GTIN is used for querying the GTIN (Global Trade Item Number) of device (refer 

to data flow path 6 (Page 23)). 

Parameter 

The following table shows the parameters of the function block: 

 

Parameter  Declaration  Data type  Memory 

area 

Description 

READ 

Input 
 
 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Query the GTIN of device upon a rising edge. 

DEV_TYP

E 

USInt 

I, Q, M, D, 

L or Con-

stant 

Select the device type: 

•

 

1: Control gear 

•

 

2: Input device (Sensor) 

ADDRES

S 

USInt 

I, Q, M, D, 

L or Con-

stant 

Specify the short address of the device. 
Range: 0 to 63 

CM_DALI  InOut 

"DALI_CT

RL" 

 

The data block of DALI_CTRL specifies the CM 1xDALI which com-

municates with the current function block. 

BUSY 

Output 

BOOL 

I, Q, M, D, 

L 

Status parameter: 

•

 

BUSY = 0: Processing of job is terminated. 

•

 

BUSY = 1: Job is still being committed. 

ACTIVE 

BOOL 

I, Q, M, D, 

L 

Status parameter: 

•

 

ACTIVE = 0: Job is not yet started. 

•

 

ACTIVE = 1: Job is being executed. 

DONE 

BOOL 

I, Q, M, D, 

L 

Status parameter: 

•

 

DONE = 0: Job is not yet started or still executing. 

•

 

DONE = 1: Job is executed without errors. 

 

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Отзывы:

Нет отзывов