manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 15 / 126

Поделиться
Скачать
Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 15

Wiring 

 

3.1 Important notes on using the device 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

14

 

Manual, 06/2019, A5E46959434-AA 

General notices on use in hazardous areas according to FM 

 

 

WARNING 

Requirement for the installing enclosure 
If the equipment is installed within an ultimate enclosure, the inner service temperature of 

the enclosure corresponds to the ambient temperature of the module. 

 

 

WARNING 

Risk of burn injury 
If a device is operated in an ambient temperature of more than 50 °C, the temperature of 

the device housing may be higher than 70 °C. The device must therefore be installed so 

that it is only accessible to service personnel or users that are aware of the reason for 

restricted access and the required safety measures at an ambient temperature higher than 

50 °C. 

 

 

WARNING 

Explosion hazard 
Do not disconnect equipment unless power has been switched off or the area is known to 

be non-hazardous. 

 

 

WARNING 

Cable 
The equipment is intended to be installed within an enclosure/control cabinet. The inner 

service temperature of the enclosure/control cabinet corresponds to the ambient 

temperature of the module. Use cables with a maximum permitted operating temperature of 

at least 30 °C higher than the maximum ambient temperature. 

 

 

WARNING 

Hazardous location 
The equipment shall only be used in an area of not more than pollution degree 2. 

 

 

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Отзывы:

Нет отзывов