Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 28

Страница: 28 / 126

Programming

5.3 System function blocks

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)
Manual, 06/2019, A5E46959434-AA

●

The FB receives and reports the event messages which are sent be the DALI-2 input

devices.

●

When Bit 1 or Bit 2 of the CM_STATUS show "1", all the other DALI function blocks

cannot be executed. You can choose any of the following actions to resume the status of

CM 1xDALI.
–

Set the input CM_RESET to 1.

–

Send the DALI command "STOP QUIESCENT MODE" or "ENABLE APPLICATION

CONTROLLER" (refer to IEC 62386-103) to the CM 1xDALI through other DALI

application controllers.

●

A defined set of messages and their content are shown at the inputs EVENT_MSG,

EVENT_SCHEME, EVENT_SRC_1, EVENT_SRC_2 and EVENT_INFO.

●

Other generic event messages are shown at the outputs RSV_MSG, RSV_MSG_LEN

and RSV_MSG_VAL. The content is shown without interpretation at the output

RSV_MSG_VAL.

Parameter

The following table shows the parameters of the function block.

Parameter Decla-

ration

Data

type

Memory

area

Description

HW_ID

Input

HW_IO

I, Q, M,

D, L or

Constant

The hardware identifier of the CM 1xDALI

CM_RES

BOOL

I, Q, M,

D, L or

Constant

Stop quiescent mode and re-enable the DALI application controller upon a

raising edge. After this action, Bit 1 and Bit 2 of the CM_STATUS will be

reset to 0.

CONN_E

Output

BOOL

I, Q, M,

D, L

The status of CPU communication with CM 1xDALI:

•

CONN_ERR = 0: No error when the CPU communicates with CM

1xDALI.

•

CONN_ERR = 1: Error occurs when the CPU communicates with CM

1xDALI.

CM_STAT

DWORD I, Q, M,

D, L

Indicate the status of the CM 1xDALI:
16#00000000: The status of the CM 1xDALI is OK.
For the detailed explanation for each Bit of the CM_STATUS, refer to the

following section "Parameter CM_STATUS".

EVENT_M

BOOL

I, Q, M,

D, L

The status of the sensor event. When the CM 1xDALI receives a sensor

event, the EVENT_MSG remains true for one cycle:

•

EVENT_MSG = 0: No sensor event

•

EVENT_MSG = 1: A sensor event is received.

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы:

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 28 / 126

Результаты поиска

Содержание SIMATIC ET 200SP CM 1xDALI

Отзывы: