manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Руководство пользователя, Страница: 4 / 126

Поделиться
Скачать
Siemens SIMATIC ET 200SP CM 1xDALI Скачать руководство пользователя страница 4

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

3

 

Preface 

 

 

Purpose of the documentation 

This manual supplements the system manual ET 200SP distributed I/O system. Functions 

that generally relate to the system are described in this manual. 
The information provided in this manual and in the system/function manuals supports you in 

commissioning the DALI system controlled by the ET 200 SP CM 1xDALI.  

Conventions 

●

 

STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the 

configuration and programming software "STEP 7 (TIA Portal)". 

●

 

In a DALI system many input devices are sensors. Therefore in this documentation the 

terms “sensor” and “input device” are used as synonyms to improve readability. 

This documentation contains figures of the described device. The figures may differ slightly 

from the devices supplied. 
Please also observe notes marked as follows: 

 

 

Note 
A note contains important information on the product described in the documentation, on the 

handling of the product or on the section of the documentation to which particular attention 

should be paid. 

 

 

Note 
To prevent injury, read the manual before use. 

 

 The manual is delivered online, you can download the document from Central technical 

support (

https://support.industry.siemens.com/cs/ww/en/

). 

Recycling and disposal 

For environmentally friendly recycling and disposal of your old equipment, contact a certified 

electronic waste disposal company and dispose of the equipment according to the applicable 

regulations in your country. 

Security information 

Siemens provides products and solutions with industrial security functions that support the 

secure operation of plants, systems, machines and networks. 

Содержание SIMATIC ET 200SP CM 1xDALI































































































































Отзывы:

Нет отзывов