Siemens SIKOSTART 3RW34, Инструкция по эксплуатации

Страница: 5 / 48

Siemens Energy & Automation, Inc. 5
1 1 IIn nttrro od du uc cttiio on n
1.1 Scope of Manual
This manual provides an overview for the installation, setup and
operation of the Siemens SIKOSTART 3RW34 controller.
Maintenance data consists of troubleshooting and spare parts
information. Note that the instructions in this manual do not
cover all details or variations in equipment, nor provide for every
possible contingency to be met in connection with installation,
operation, or maintenance.
1.2 3RW34 SIKOSTART Features
The SIKOSTART 3RW34 product line is the next generation of
Siemens solid state reduced voltage controllers. This controller com-
bines DSP microprocessor and SCR technologies to provide AC
induction motor starting and operation. The sturdy compact frame
affords rugged, industrial grade reliability.
The SIKOSTART 3RW34 controller is a single ramp style con-
troller using phase control for the operation of three-phase
induction motors. The controller can be set to operate either
wye (star) or delta type motors. Each unit includes soft start and
stop parameters plus fault detection. The controller can be used
with an electro-mechanical starter or, when combined with an
overload relay, the controller can be used as a solid-state starter.
The SIKOSTART 3RW34 controller is available as an open type
(compact frame, no enclosure) or in a NEMA 1, 3R, 4, or 12
enclosure. The unit can be ordered as a starter with overload
relays or as a combination starter with disconnecting means and
circuit overload protection devices. Additional options are also
available such as push buttons, pilot lights, and meters.
1.3 Applications and Benefits
Typical applications for the SIKOSTART 3RW34 controller are to
soft start and soft stop AC induction motor driven equipment
such as fans, pumps and compressors.
Applications also
include controlling machines with gearbox, belt or chain drive
elements, such as: conveyors, sanders, planers, saws, packag-
ing machines and punch presses.
Using the SIKOSTART 3RW34 controller provides benefits to
the drive system in the following ways:
1 )the life of mechanical drive transmission elements is
extended, e.g., gearbox jerking is substantially reduced
resulting in less wear and tear;
2) reduced starting current relieves the supply network of cur-
rent peaks; and
3) smoother acceleration of loads eliminates process or product
damage.
2 2 O Op pe erra attiin ng g P Prriin nc ciip plle e
2.1 Function Overview
The SIKOSTART 3RW34 controller utilizes a voltage ramp design
to produce an output voltage to the motor that increases from a
customer selected initial voltage to full line supply voltage over
an adjustable starting time. This “voltage ramp” produces a
reduced current start (soft start) similar to a current limit start
without the load dependence of the current limit type start.
Similarly, stopping time can be adjusted to provide a soft stop
for many pumping applications.
The SIKOSTART controller employs a DSP (digital signal proces-
sor) to control the motor. This advanced type of microprocessor
allows the controller to “contour” the starting and stopping
ramps. This contour adjusts for the nonlinearities of an induction
motor to produce a smoother and more linear motor start and
stop.
2.2 Functional Description
Power Poles. As is shown in the block diagram of figure 1, the
incoming main power (L1, L2, L3) is connected to the con-
troller’s three power poles which control the voltage to the
motor windings. Each power pole consists of two SCR’s in a
back-to-back arrangement for each phase which allows alternat-
ing current to pass to the motor.
Snubber PCB. The snubber printed circuit board(s) contains the
trigger circuit for each SCR. The firing signal for each trigger cir-
cuit is generated at the logic printed circuit board. The snubber
board sensing circuits send data to the logic board for factoring
into firing signal generation. The snubber board also includes an
RC network for a degree of protection against false firing of the
SCR’s due to dv/dt and MOV’s for transient protection.