manualshive.com logo in svg

Siemens SIJECT 16i, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIJECT 16i Скачать руководство пользователя страница 41

SIJECT OP15B Screens

SIJECT 16i   Operation Manual

3-15

3.1.4  Temperature screen

Fig 3-16

Temperature screen 1

Operating sequences

Press  this  key  to  enter  the  Temperature  screen  1.  See  Fig  3-16,
Temperature screen 1.

This  screen  consists  of  five  temperature  channels  for  barrel  and  one
channel  for  oil  temperature.  Temperature  values  for  each  channel  can  be
set  on  this  screen.  For  the  nozzle,  either  open  loop  or  close  loop  can  be
selected.

If  the  nozzle  is  under  open  loop  control,  the  indicator  at  “Open  loop”  will
backlight. Users can set a percentage value in Nozzle block so as to make
sure the  percentage  of heating on/off in a time base. For  example,  if  time
base is 20s, and nozzle is set as 30%. Then heating time is 20 x 30% = 6s
and heating off time is 14s.

If the nozzle is under close loop control, the upper and lower tolerance can
be set here which is valid for all temperature zone. When the temperature
is within specification, channel heating will maintain the temperature within
this range. The indicator 

 (see table 3-1) will stop flashing, which means

the screw can work at this situation.

If  Hold  function  is  selected,  the  block  of  Holding  will  backlight.  Holding
temperature can be set for each temperature channel.

The unit of temperature will be 

°

C.

Notice

Here, the thermocouple should only be type K.

Nozzle open loop control: no thermocouple is mounted on nozzle. Nozzle
heating can be executed via heater on/off.

For the selection of open loop / close loop, please refer to section “3.1.10
Service screen --- temperature setting”.

Содержание SIJECT 16i
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды