Siemens SCALANCE XR-300WG Скачать руководство пользователя страница 29

Страница: 29 / 100

4.5

RESET button

WARNING

EXPLOSION HAZARD

Do not press the RESET button if there is a potentially explosive atmosphere.

Position

The "RESET" button is located on the front of the SCALANCE XR-300WG.

5(6(7

Figure 4-1

Position of the "RESET" button on the SCALANCE XR-300WG

Resetting the device to factory defaults

NOTICE
Previous settings

If you reset, all the settings you have made will be overwritten by factory defaults.

NOTICE
Inadvertent reset

An inadvertent reset can cause disturbances and failures in the configured network.

Requirement
• The device is in operation.

• The function "Reset to factory defaults" is enabled for the RESET button.

Note
Reset despite disabled "RESET" button

If you have disabled the "Reset to Factory Defaults"function for the "RESET" button in the
configuration, this does not apply during the startup phase, see section "Restoring the
factory settings (Page 70)"

If the function has been disabled in the configuration, it is only disabled on completion of the
startup phase.

Description of the device

4.5 RESET button

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Содержание SCALANCE XR-300WG





































































































Результаты поиска

Содержание SCALANCE XR-300WG

Отзывы:

Похожие инструкции для SCALANCE XR-300WG

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-300WG, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-300WG

Отзывы:

Похожие инструкции для SCALANCE XR-300WG

Бренды по названию

Популярные бренды