Siemens SCALANCE XR-300WG Скачать руководство пользователя страница 47

Страница: 47 / 100

5.5.3

Removing a pluggable transceiver (SFP)

Notes on deinstallation

CAUTION

Risk of burns due to the high temperatures of the pluggable transceiver

The pluggable transceivers can be plugged and pulled during operation. Leave the transceiver
to cool down as much as possible.

Procedure

Follow the steps below to remove a pluggable transceiver:

1. Remove the connecting cable of the pluggable transceiver.

2. Open the clip of the pluggable trabsceiver.

3. Remove the pluggable transceiver from the pluggable transceiver slot.

Note
Do not use force

It must be possible to remove the pluggable transceiver easily and without applying any
force.

4. Close the pluggable transceiver slot with a sealing plug.

Installation

5.5 Inserting and removing pluggable transceivers

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Содержание SCALANCE XR-300WG





































































































Результаты поиска

Содержание SCALANCE XR-300WG

Отзывы:

Похожие инструкции для SCALANCE XR-300WG

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-300WG, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-300WG

Отзывы:

Похожие инструкции для SCALANCE XR-300WG

Бренды по названию

Популярные бренды